6254
8161 2200 0000
Ready to ship today, Delivery time appr. 1-3 workdays
Important info about the delivery time
€291.06 *
incl. VAT plus shipping costs
Leave your email address and stay informed about this article.
as soon as the item is back in stock
as soon as the item drops in price
as soon as the item is available as a special offer
Wind and rain control WRS 2b In the event of wind / rain, a closing command is sent to SHEV... more
Wind and rain control WRS 2b
- In the event of wind / rain, a closing command is sent to SHEV control panels or ventilation control units. Four separate potential-free changeover contacts (output contacts) provide the required signal. The contacts remain active as long as a sensor has responded, but at least for 6 minutes
- Connection of a wind sensor WM or rain sensor RS is required
- Wind and rain sensitivity adjustable
- Selectable functions:
- - "Reduced wind sensitivity" (to close, equally strong wind must last longer)
- - "Continuous heating" (the rain sensor is heated continuously)
- - "Contact programming" (contacts 3 and 4 switch alternatively in case of wind and/or rain)
- - "Output deactivated" (deactivate all output contacts for service / maintenance purposes)
- - "Reduced closing time" (the minimum closing time is reduced from 6 to 3 minutes)
- - "Fault contact" (contact 2 switches in the event of a rain sensor fault)
- - "Test" (mode for testing the function of sensors and drives)
- Displays for operation I, wind W and rain R
- Plastic housing, light gray (RAL 7035)
Technical data:
- Mains voltage supply: 230 V~ / 50 - 60 Hz
- Power consumption: 0,09 A
- Dimensions in mm (W x H x D): 165 x 155 x 75
- Cable feed through membrane grommets (from below): 4 x M16
- Ambient temperature: -5 °C ... +40 °C
- Relative humidity: 20 % ... 80 %, non-condensing
- Housing protection class (according to DIN EN 60529): IP40 (Option SG: IP54)
- Not suitable for outdoor use. Protect from direct sunlight, moisture and excessive dust! Preferably, installation should take place in dry, heated rooms.
- The controller complies with the requirements of the directives 2006/95/EC and 2004/108/EC (interference emission: EN 61000-6-3 and EN 55022, interference immunity: EN 61000-6-2 and EN 50130-4).
- Inputs / outputs, fuses:
- Wind sensor WM, heated rain sensor RS: 1 each
- Adjustment range of wind sensitivity: approx. 5 - 15 m/s (approx. 20 - 60 km/h, about wind force 3 - 7)
- Adjustment range of rain sensitivity: light - heavy rain
- 4 change-over contacts, load capacity: 5 A / 30 V- / 230 V~
- Output contacts (G-fuse link 5 x 20 mm): F1 - F4: F 5 A
- Mains primary (G-fuse link 5 x 20 mm): F5: T 125 mA
Data sheet/instructions can be found under "Downloads".
Photos, videos and diagrams: Source © K+G Pneumatik GmbH
Technical advice
+49 9282 48731-15
technik@bsc-technology.de
Fast delivery
... of goods in stock. Orders placed before 14:00 are usually shipped the same day.
Questions about the article
What do you have to look out for when you want to connect a wind and/or rain detector to a SHEV control panel or ventilation system? We will give you a few tips to ensure that you choose the right product.
Technical data more
Scope of delivery: | Control |
Dimensions: | in mm (W x H x D): 165 x 155 x 75 |
Scope of delivery & accessories more
Downloads more